文章摘要
何雯,陈满儒.薄型烟机包装实验室测试与跌落仿真分析[J].包装工程,2019,40(3):125-130.
HE Wen,CHEN Man-ru.Laboratory Test and Drop Simulation Analysis of Thin-type Kitchen Ventilator Package.Packaging Engineering,2019,40(3):125-130.
薄型烟机包装实验室测试与跌落仿真分析
Laboratory Test and Drop Simulation Analysis of Thin-type Kitchen Ventilator Package
投稿时间:2018-09-26  修订日期:2019-02-10
DOI:10.19554/j.cnki.1001-3563.2019.03.018
中文关键词: 跌落测试  扫频测试  模态分析  跌落分析
英文关键词: drop test  sweep frequency test  modal analysis  drop analysis
基金项目:
作者单位
何雯 陕西科技大学 轻工科学与工程学院西安 710021 
陈满儒 陕西科技大学 轻工科学与工程学院西安 710021 
摘要点击次数: 119
全文下载次数: 167
中文摘要:
      目的 研究薄型烟机包装跌落状态下的变形问题,并根据测试及仿真分析结果提出整改方向和具体措施。方法 根据运输包装件跌落试验方法确定导致产品变形的跌落工况,基于Creo和Ansys Workbench软件进行产品包装件跌落仿真分析,得到产品的位移及应力分布。结果 扫频测试共振频率与模态分析固有频率一致,证明了有限元模型建立的正确性;跌落过程中能量守恒证明了分析结果的正确性;最大位移分布于滤网、蜗壳、电机上,最大应力分布于产品外壳上;实验室测试与仿真分析得到的加速度随时间的变化趋势基本相同。结论 分析产品跌落变形问题可采用实验室测试与有限元仿真分析相结合的方法,全面评价产品变形情况和应力集中现象。解决薄型烟机变形问题可通过增加衬垫、改进产品结构等方式实现。有限元模型的验证和分析过程中的能量守恒能够保证有限元分析结果的正确性。
英文摘要:
      The work aims to study the deformation of the thin-type kitchen ventilator package under drop condition, and put forward the rectification direction and specific measures according to the test and simulation analysis results. The drop condition causing product deformation was determined according to the drop test method of transport packages. Based on Creo and Ansys Workbench software, the drop simulation analysis of product packages was carried out, and the displacement and stress distribution of products were obtained. The consistency between resonance frequency measured by sweep frequency test and the natural frequency of modal analysis proved that the finite element model established was reasonable. The conservation of energy in the drop process proved that the analysis result was correct. The maximum displacement was distributed on filter, volute and motor. The maximum stress was distributed on the product shell. In addition, the trend of acceleration obtained from laboratory test varying with time was basically the same with that obtained by simulation analysis. In order to analyze the drop deformation of products, laboratory tests and finite element simulation analysis can be combined to comprehensively evaluate the deformation and stress concentration of products. The deformation problem of the thin-type kitchen ventilator can be solved by adding pads and improving the product structure, etc. The validation of the finite element model and the conservation of energy in the analysis process can ensure the correctness of the finite element analysis results.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第6329245位访问者    渝ICP备10003521号-2

版权所有:《包装工程》编辑部 2014 All Rights Reserved

邮编: 电话:023-68792294传真: Email:

    

渝公网安备 50010702501716号