文章摘要
柴德望,丁千,张泉.一种利用重叠分离机制进行纸张分离的变形力研究[J].包装工程,2018,39(21):139-143.
CHAI De-wang,DING Qian,ZHANG Quan.Deformation Force of Paper Sheet Separated by the Overlap Separation Mechanism[J].Packaging Engineering,2018,39(21):139-143.
一种利用重叠分离机制进行纸张分离的变形力研究
Deformation Force of Paper Sheet Separated by the Overlap Separation Mechanism
投稿时间:2018-07-19  修订日期:2018-11-10
DOI:10.19554/j.cnki.1001-3563.2018.21.025
中文关键词: 重叠分离机构  弹性梁模型  三弯矩定理  变形力
英文关键词: overlap separation mechanism  elastic beam model  theorem of three moments  deformation force
基金项目:柴德望(1984—),男,博士,主要研究方向为摩擦分析、非线性动力学。
作者单位
柴德望 1.天津大学 力学系天津 300350 
丁千 1.天津大学 力学系天津 300350 
张泉 2.恒银金融科技股份有限公司博士后科研工作站天津 300308 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 研究纸张在重叠分离送纸机构中所受变形力的特点,为纸张运动摩擦分析提供依据。方法 首先推导公式得出纸张正常分离条件,把纸张作为弹性梁模型,利用Clapeyron三弯矩定理分析纸张表面的变形力。结果 纸张在重叠区域变形力正比于交叠量;剥离轮的宽度越大,变形力越大;变形力随着剥离轮与送钞轮的左边距的增加先减小后增大;送钞轮宽度对变形力的影响不大。结论 通过对弹性梁模型的分析,获得了纸张在重叠区域变形力随结构参数变化的影响规律,并得到了能使纸张受力均衡的剥离轮和送钞轮的左边距值,为重叠机构的设计提供参考。
英文摘要:
      The work aims to study the deformation force features of the paper sheet which is passing through the overlap separation mechanism to provide basis for its kinetic friction analysis. Firstly, the formula was derived to obtain the normal separation condition of paper sheet. Then, with the paper sheet as the elastic beam model, the deformation force acting on the paper sheet surfaces was analyzed with the Clapeyron’s theorem of three moments. The results showed that the deformation force of paper sheet in the overlap area was proportional to the overlap. The wider the gate-roller was, the greater the deformation force was. The deformation force decreased and then increased with the increase of the edge distance of the gate-roller and feed-roller at the left side. The width of the feed-roller had hardly any effect on the deformation force. Based on the analysis of elastic beam model, the law of influence of paper sheet's deformation force in the overlap area changing with the structural parameters is obtained and the values of the edge distance of the gate-roller and feed-roller at the left side are acquired to provide reference for the design of overlap mechanism.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第20789073位访问者    渝ICP备15012534号-2

版权所有:《包装工程》编辑部 2014 All Rights Reserved

邮编:400039 电话:023-68795652 Email: designartj@126.com

    

渝公网安备 50010702501716号