文章摘要
黄绍祥,杨传民,常淑英,何思念.喷涂参数及带速对大豆蛋白液喷涂平均密度的影响[J].包装工程,2016,37(23):78-82.
HUANG Shao-xiang,YANG Chuan-min,CHANG Shu-ying,HE Si-nian.Effects of Spraying Parameters and Belt Velocity on the Soybean Protein’s Average Spraying Density[J].Packaging Engineering,2016,37(23):78-82.
喷涂参数及带速对大豆蛋白液喷涂平均密度的影响
Effects of Spraying Parameters and Belt Velocity on the Soybean Protein’s Average Spraying Density
投稿时间:2016-07-05  修订日期:2016-12-10
DOI:
中文关键词: 大豆蛋白液  平均密度  喷涂参数  带速  图像处理
英文关键词: soybean protein solution  average density  spraying parameters  belt velocity  image processing
基金项目:天津市自然科学基金重点项目(15JCZDJC34100);天津市高校发展基金(20130403);天津市高等职业技术教育研究会课题(XV307)
作者单位
黄绍祥 天津商业大学天津 300134 
杨传民 天津商业大学天津 300134 
常淑英 1.河北工业大学天津 3001312.天津电子信息职业技术学院天津 300350 
何思念 天津商业大学天津 300134 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 研究大豆蛋白喷涂在硫酸纸上的平均密度,以及喷涂参数和带速对喷涂平均密度的影响。方法 首先通过摄像机采集喷涂图像,再运用Matlab软件处理计算大豆蛋白液所占面积比。面积比越大,则大豆蛋白喷涂效果越好,并利用响应面分析法研究喷涂参数及带速对喷涂平均密度的影响。结果 当液压为159 Pa,气压为180 Pa,带速为11.93 mm/s时,大豆蛋白液所占面积比可达79.9079%,此时最佳。结论 单个因素中液压和带速对喷涂平均密度有显著影响。通过分析软件建立了大豆蛋白液所占面积比与喷涂参数及带速之间的关系模型,并得到了最佳喷涂条件。
英文摘要:
      The work aims to research the average density of soybean protein spraying on the parchment paper and the influence of spraying parameters and belt velocity on the average spraying density. Firstly, the spraying image was collected by the camera and then the area ratio of soybean protein solution was processed and calculated by software Matlab. The larger the area ratio was, the better the spraying effect of soy protein was. The effect of spraying parameters and belt velocity on the average spraying density was also studied based on response surface analysis. When hydraulic pressure was 159 Pa, air pressure was 180 Pa and belt velocity was 11.93 mm/s, the area ratio of soybean protein solution could be up to 79.9079%, which was the best. Among the single factors, the hydraulic pressure and belt velocity has a significant effect on the average spraying density. The relational model between the area ratio of soybean protein solution and the spraying parameters & belt velocity is built through analysis software, and the optimal spraying conditions are identified.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第21150462位访问者    渝ICP备15012534号-2

版权所有:《包装工程》编辑部 2014 All Rights Reserved

邮编:400039 电话:023-68795652 Email: designartj@126.com

    

渝公网安备 50010702501716号