文章摘要
汤亮,郭卫林,龚发云,王亮,潘明铮,张董洁.基于 FLUENT 的摇盖式异形盒烟支入盒工艺优化设计[J].包装工程,2016,37(11):71-77.
TANG Liang,GUO Wei-lin,GONG Fa-yun,WANG Liang,PAN Ming-zheng,ZHANG Dong-jie.Technology Optimization Design of Packing Cigarettes into Shake-lid Shaped Cigarette Case Based on FLUENT[J].Packaging Engineering,2016,37(11):71-77.
基于 FLUENT 的摇盖式异形盒烟支入盒工艺优化设计
Technology Optimization Design of Packing Cigarettes into Shake-lid Shaped Cigarette Case Based on FLUENT
投稿时间:2015-10-19  修订日期:2016-06-10
DOI:
中文关键词: 摇盖式异形烟盒  机械手  真空吸盒  数值模拟
英文关键词: shake-lid shaped cigarette case  manipulator  vacuum chuck  numerical simulation
基金项目:湖北省自然科学基金重点项目(2012FFA059)
作者单位
汤亮 湖北工业大学武汉 430068 
郭卫林 湖北工业大学武汉 430068 
龚发云 湖北工业大学武汉 430068 
王亮 湖北工业大学武汉 430068 
潘明铮 湖北工业大学武汉 430068 
张董洁 湖北工业大学武汉 430068 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 针对摇盖式异形烟盒烟支入盒工艺普遍使用手工包装,导致生产效率低下且易产生二次污染等问题,提出使用真空吸附式机械手完成烟支入盒流程,并对机械手末端真空吸盒的结构进行优化设计。方法 应用 FLUENT 软件对 3 种不同结构型式真空吸盒的二维流场进行数值模拟分析,得到吸盒端口结构型式及真空度与负压气流场稳定性的影响关系。 结果 负压气流场稳定性强弱关系为锥形>圆形>方形;随着真空度的增加,吸盒端口中心及吸孔入口流速均增加,负压气流场内真空度越大,其稳定性越差,当真空度分别为 20, 25, 30, 40 kPa 时,锥形吸盒气流场的理想真空度为 20 kPa。 结论 设计的烟支入盒工艺合理,稳定性好,效率高。模拟结果可给真空吸盒的优化设计提供理论依据。
英文摘要:
      A lot of manpower is used in the process of packing cigarettes into shake-lid shaped cigarette case, which results in low production efficiency and easily leads to secondary pollution problem. Vacuum suction manipulator was proposed to conduct this packing process and optimization design was performed for the structure of vacuum chuck in the end of manipulator. FLUENT was used to analyze the 2D flow fields of chucks with three kinds of different structural parameters, obtaining the relationship among vacuum flow field stability and sucker-port structure, degree of vacuum. Simulation results showed that the relationship strength of the vacuum flow field followed the order of Cone> Round> Square; With the increase of the degree of vacuum, the hole inlet flow rate of sucker port center and the suction both increased. The larger the vacuum degree inside the vacuum flow field, the worse the stability. When the vacuum pressure was 20, 25, 30, 40 kPa, the ideal degree of vacuum chuck cone flow field was 20 kPa. The design of cigarettes into the box process was reasonable, stable and efficient. The simulation results could provide theoretical basis for optimization design of vacuum chuck.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第20815350位访问者    渝ICP备15012534号-2

版权所有:《包装工程》编辑部 2014 All Rights Reserved

邮编:400039 电话:023-68795652 Email: designartj@126.com

    

渝公网安备 50010702501716号