文章摘要
苑静,刘少友.水溶性聚氨酯热熔胶的制备[J].包装工程,2014,35(17):65-68.
YUAN Jing,LIU Shao-you.Preparation of Water-soluble Polyurethane Hot Melt Adhesive[J].Packaging Engineering,2014,35(17):65-68.
水溶性聚氨酯热熔胶的制备
Preparation of Water-soluble Polyurethane Hot Melt Adhesive
投稿时间:2013-12-06  修订日期:2014-09-01
DOI:
中文关键词: 水溶性  聚氨酯热熔胶  聚乙二醇  甲苯二异氰酸酯
英文关键词: water-soluble  polyurethane hot-melt adhesive  polyethylene glycol  toluene diisocyanate
基金项目:科技创新人才团队建设项目([2013]4029)
作者单位
苑静 凯里学院 凯里 556011 
刘少友 凯里学院 凯里 556011 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 制备水溶性聚氨酯热熔胶。 方法 用聚乙二醇(PEG)和甲苯二异氰酸酯(TDI)为原料, 制备水溶性聚氨酯热熔胶, 研究了 PEG的相对分子质量、TDI 滴加温度、原料配比和反应时间等对水溶性聚氨酯热熔胶性能的影响。 结果 当 PEG8000, PEG600, PEG200, 乙二醇和 TDI 的摩尔比为 1∶1∶0.8∶1∶4, TDI的滴加温度为 60~ 70 ℃、反应时间为 4 h时, 所得水溶性聚氨酯热熔胶的软化点为 59.5 ℃、粘接强度为 2.668 MPa。 结论 制备的水溶性聚氨酯热熔胶可以作为电子产品零配件等工业半成品的表面保护膜。
英文摘要:
      Objective To prepare the water-soluble polyurethane hot melt adhesive. Methods Water-soluble polyurethane hot melt adhesive was prepared using polyethylene glycol (PEG) and toluene diisocyanate (TDI) as raw materials. The effects of PEG molecular weight, raw material ratio, TDI addition temperature, and reaction time on product properties were discussed. Results At a PEG8000∶PEG600∶PEG200∶glycol∶TDI molar ratio of 1∶1∶0.8∶1∶4, a TDI addition temperature of 60~ 70 ℃, and a reaction time of 4 h, the as-obtained product exhibited a softening point of 59.5 ℃, and an adhesive strength of 2.668 MPa. Conclusion This water-soluble polyurethane hot melt adhesive could be used as surface protection film of industrial semi-finished products.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第20790905位访问者    渝ICP备15012534号-2

版权所有:《包装工程》编辑部 2014 All Rights Reserved

邮编:400039 电话:023-68795652 Email: designartj@126.com

    

渝公网安备 50010702501716号